I’m beginning the restoration of my Dad’s Elan S3 DHC. It’s been off the road since the early 90’s and has unfortunately spent a good few years exposed to the elements. The doors are seized shut and we just can’t figure out how to release them! The key doesn’t seem to do anything, the interior door release handles work and we can see the mechanism moving on the passenger door but it’s not releasing. I’ve dismantled the lock on the drivers door from the inside and have tried to free it with a screwdriver but no joy.
Has anyone experienced this and found a way around it? I’m reluctant to drill the lock from the outside and also not even sure if that will help.
Since it’s a DHC you should be able to work this out, I would first try to look at the locks from the inside of the door (removing the upholstery), spraying generously some WD40 or the like on the lock mechanism and let penetrate before wiggling, possibly with the help of a bend screwdriver if it does not work (make sure the safety lock is off before too strong of a wiggle). If after a couple days and applications of WD40 etc it still resists, undoing the hinges may allow you to wiggle some more… but I think it won’t be necessary (plus the hinges securing nuts will need some WD40, too)
WD-40 is not a penetrating oil, it’s a water displacer. As in “WD”. It will not dissolve rust, only displace water from it. (It is also not a lubricant once it dries.) The only good automotive uses for it are displacing water from locks and “drying” damp ignition wires.
You really need Kroil from Kano Labs. Best stuff ever if you’re going to work on anything old with iron or aluminum in it. Liquid Wrench and PB Blaster are way behind the power of this stuff if you can’t get Kroil on your side of the pond, but at least they are penetrating oils.
No personal interest, I’ve just never found anything Kroil can’t free. Just laid in a new stock which should be arriving soon.
If you decide to remove the hinges, it can be done fairly easily with the right tools after removing the door card.
Be aware that the actual hinge pin is cut & threaded from nylon rod about 1 inch diameter (item 3 in the diagram) It is secured with a lock plug (item 4) which you must remove first. For this you will need an appropriate sized socket wrench and probably an extension rod. Use the Plus-Gas first to loosen the threads.
The nylon hinges have domed ends which locate in cup shaped supports in the fibreglass body of the car. The rear end of the nylon hinge has a square hole in it for a square rod (about 1/4 inch across flats; you need ensure that your tool is a good fit. I found that the interior rod of a typical in-house door handle is the correct fit. You will need an appropriate socket adaptor and preferably a ratchet socket-set bar to unscrew it. Tap the square rod all the way into the nylon (about 1/2 inch (?) else you may damage the square hole in the nylon when you try to twist it, (which will create a REAL problem).
You may need to only undo either the top nylon hinge or the bottom one before the door becomes loose enough to remove. Avoid loosening the bolts that hold the hinge holder to the door, because these determine the fit of the door into the body and are a real pain to get right again.
The dome on the hinges can seize and be a pain to remove. If you are considering doing quite a bit of renovation then the hinges may well be coming off anyway. I agree that they are a time consuming item to fit back in the right spot but it’s not rocket science, merely time consuming. In your situation for ease and speed I would remove the 2 bolts holding the hinge bracket (2) and ease the door outwards at the front then pull forward away from the lock at the rear which only has lateral constraints, not forward and back.
So I’ve got the bottom hinge off, I just undid the 2 bolts holding the bracket. Everything needs to be stripped and cleaned up/replaced anyway.
The door comes away from the body at the bottom but obviously can’t access the upper hinge until the door opens.
This has given a bit more wiggle and play but still can’t release the door. I’ve just started to work around it for now, and continue stripping the rest of the car.
Is there anywhere I can get a detailed diagram of how the S3 door lock works? I have the parts catalogue, and the workshop manual but neither give a detailed description. Just wondering if there is a way I can release it with a slim poker through the gap between the body and the door. I can see the striker but not sure how to release it
Does the other door work? I find the S3 latching/lock mechanism the easiest to understand. If the
other side opens, you should be able to get an idea on what is not working on your non-op side. The
key will be needed to move a lever to allow the latch mechanism to come away from its mounting on
the window frame. A bit fiddly.
Best of luck finding that black escutcheon. I carried a sample around for several years to car shows and fairs.
Eventually Steve Broad on here gave me one. I haven`t forgotten that.
Eric in Burnley
1967 S3SE DHC